n18 Oscillator topics (free-running)
Oscillators with ceramic resonators, see page n19
Xtal oscillators, see page n20
Note: On this page is shown oscillators which are also found on the other pages on this site.
Audio oscillator using 88 or 77mH toroid coil (pupin coil for telephone line). Just a reference circuit, but one may sometimes need such; perhaps for another frequency. It was made, based on experience with 50kHz BFO for Drake 2-B, and later alternative BFO for R-4 - CW-meteorscatter product detector as plug-in unit on the rear of the receiver.
(The oscillator is also shown on pg c11).
2100Hz oscillator with TBA120 as low frequency mixer. The circuit is shown as a reference, several other devices may be better, but it is important to check which input has the right phase relation to an output to use it as oscillator. The oscillator uses a Wien-bridge (Vienna Bridge?) type oscillator with the limiter. If you wish to use inductors it is no reason for using this oscillator at all, then the oscillator type using 77 or 88mH inductor may be a suggestion. Some publications are spread using this device as audio up-converter for CW Meteorscatter reception, you'll find some with Google-search for "la8ak".(The oscillator is also shown on pg c11).
195-200kHz Clapp-oscillator for MOSFET mixer.
The power gain for this simple dual-gate mosfet mixer is rather high. It was soon learnt that in spite
that I didn't hear MSF when listening to 60kHz (with the active aerial), it did break through the IF, and 40dB
IF rejection was neccessary with active aerial on 136kHz at this QTH in (Kristiansand, Loc: JO38XC, South Norway),
therefore it is shown a two stage input filter.
German transceiver 15W.S.E.a RX mixer and Local Oscillator
Note the cathode injection on detector (using battery-type valve RV2,4P700) to the left side of the circuit diagram, a comparable circuit is found in WS38 where the local osc has signal tapped from the filament side. See more details on page 31a
Seiler type VFO, constructed for the receiver (the doubler is not shown on this circuit diagram). I was later told that the ratio between C4 and C5 is wrong, it works, but would be better with equal values - say 2x 2200pF styroflex or film type. If varying output voltage is not a problem (when driving CMOS devices), the clapp type oscillator is usually easier to construct.
It is also shown on page c21
2176-2208kHz Clapp-type variable oscillator . It was intended to be used with a divide-by-16 divider to cover 136-138kHz band, so it is no problem concerned with using a clapp oscillator with varying output level
Also shown on pg L90.
770-800kHz clapp-oscillator, as local osc. for 74HC4066-type converter . The oscillator has an output of 195-199kHz. It is easier to build a VFO on a higher frequency and divide to to 195-199kHz, since it requires more readily available coils. Little further is to be said, but I was surprised that only one stage was needed to achieve good limiting.
BF314 were chosen since it is available free in large quantities, but I suppose any 2N2222, 2N3904, BC237, BF199, BF224 and many other types would do the job just fine.
This circuit is also shown on page L1
Variable oscillator using RG174 coax cable which has been described in QST (10/1980)
Jurjen Lemstra's VFO, see Electron nr 10/90
|cable length||C2 (pF)||C3 (pF)||C1 (pF)||Frequency|
Component variations for Jurjen Lemstra's VFO
(AR nr 5/97 TR 267 pp138)
Will provide some text later
3W power oscillator for 80m using EL84/6BQ5, see page n12
Last update: 2004.07.27